/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 4/16/02
 */
 
/* Protection from multiple definitions */
#ifndef __PARAM_HEADER
#define __PARAM_HEADER
 
/* GPIB addresses */
#define GPIB_BOARD_ADDR					0
#define GPIB_PDI5025_ADDR				13
#define GPIB_HP3458_ADDR				24
#define GPIB_B9900_ADDR					17
#define GPIB_GP3_ADDR					16
#define GPIB_LS450_ADDR					15
#define GPIB_HP3457_ADDR				22
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8

/* Magnet current */
#define IMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define IMAG_DAC488_ADDR				GPIB_DAC488_ADDR
#define IMAG_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define IMAG_DAC488_PORT				2
#define IMAG_DAC488HR_PORT				1
#define IMAG_HP3457_CHAN				0
#define IMAG_CONFIG						IMAG_DAC488_HP3457
#define IMAG_BIPOLAR					IMAG_TRUE
#define IMAG_PS_AMPS_PER_DAC_VOLT		1.2
#define IMAG_TRANS_VOLTS_PER_AMP		.08
#define IMAG_RAMP_STYLE					IMAG_COSINE
#define IMAG_MAX_CURR_LIMIT				20.
#define IMAG_MIN_CURR_LIMIT				-20.
#define IMAG_RAMP_RATE					.2
#define IMAG_WAIT_AFTER_RAMP			3.
#define IMAG_STAND_RAMP_RATE			.7
#define IMAG_WAIT_AFTER_STAND_RAMP		3.
#define IMAG_INIT_ZERO_CURRENT_MEAS		IMAG_FALSE
#define IMAG_INIT_TURN_ON				IMAG_FALSE
#define IMAG_INIT_TURN_ON_CURRENT		0.
#define IMAG_SHOW_UI					IMAG_TRUE

/* Hall probe measurements */
#define BHALL_BOARD_ADDR				GPIB_BOARD_ADDR
#define BHALL_B9900_ADDR				GPIB_B9900_ADDR
#define BHALL_GP3_ADDR					GPIB_GP3_ADDR
#define BHALL_LS450_ADDR				GPIB_LS450_ADDR
#define BHALL_DEVICE_TYPE				BHALL_B9900
#define BHALL_B9900_CHAN				1

/* Voltage integration system */
#define VTRAMP_BOARD_ADDR				GPIB_BOARD_ADDR
#define VTRAMP_PDI5025_ADDR				GPIB_PDI5025_ADDR
#define VTRAMP_HP3458_ADDR				GPIB_HP3458_ADDR
#define VTRAMP_PDI5025_CHANNEL			'A'
// aluminum #define VTRAMP_PDI5025_GAIN				1000
#define VTRAMP_PDI5025_GAIN				50
#define VTRAMP_HP3458_RANGE				.1
#define VTRAMP_CONFIG					VTRAMP_PDI5025
#define VTRAMP_T_SAMP_BEFORE			0.5
#define VTRAMP_T_SAMP_AFTER				7.
#define VTRAMP_DO_OFFSET_CORRECTION		VTRAMP_TRUE
#define VTRAMP_SHOW_UI					VTRAMP_TRUE

/* BvsH module */
#define BVSH_SAMPLE_GEOMETRY			BVSH_CYLINDER
#define BVSH_CYL_HALL_PROBE_RANGE		4
#define BVSH_CYL_NUM_TURNS_MEAS_COIL	180
#define BVSH_CYL_MEAS_COIL_DIAM			.019768
#define BVSH_CYL_SAMPLE_OUTER_DIAM		.01901
#define BVSH_CYL_SAMPLE_INNER_DIAM		.00488
#define BVSH_RING_NUM_TURNS_DRIVE_COIL	200
#define BVSH_RING_NUM_TURNS_MEAS_COIL	100
#define BVSH_RING_SAMPLE_OUTER_DIAM		.050800
#define BVSH_RING_SAMPLE_INNER_DIAM		.042448
#define BVSH_RING_SAMPLE_HEIGHT			.006220
#define BVSH_SHOW_UI					BVSH_TRUE

/* Test currents */
#define BVSH_NUM_STAND_CYCLES			3
#define BVSH_STAND_MAX					12.
#define BVSH_STAND_MIN					-12.
#define BVSH_NUM_TEST_CURRENTS			61
double BVSH_TEST_CURRENTS[BVSH_NUM_TEST_CURRENTS] = {0., .05, .1, .15, .2, .3, .4, .6, .8, 1., 2., 4., 6., 8., 10., 12., 10., 8., 6., 4., 2., 1., .8, .6, .4, .3, .2, .15, .1, .05,
	0., -.05, -.1, -.15, -.2, -.3, -.4, -.6, -.8, -1., -2., -4., -6., -8., -10., -12., -10., -8., -6., -4., -2., -1., -.8, -.6, -.4, -.3, -.2, -.15, -.1, -.05, 0.};

//#define BVSH_NUM_STAND_CYCLES			3
//#define BVSH_STAND_MAX					8.
//#define BVSH_STAND_MIN					-8.
//#define BVSH_NUM_TEST_CURRENTS			37
//double BVSH_TEST_CURRENTS[BVSH_NUM_TEST_CURRENTS] = {0., .2, .4, .6, .8, 1., 2., 4., 6., 8., 6., 4., 2., 1., .8, .6, .4, .2,
//	0., -.2, -.4, -.6, -.8, -1., -2., -4., -6., -8., -6., -4., -2., -1., -.8, -.6, -.4, -.2, 0.};

//#define BVSH_NUM_STAND_CYCLES			1
//#define BVSH_STAND_MAX					5.
//#define BVSH_STAND_MIN					-5.
//#define BVSH_NUM_TEST_CURRENTS			9
//double BVSH_TEST_CURRENTS[BVSH_NUM_TEST_CURRENTS] = {0., 2., 4., 2., 0., -2., -4., -2., 0.};

/* End protection */
#endif