/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 4/16/02
 */
 
/* Protection from multiple definitions */
#ifndef __PERMEAMETERPARAM_HEADER
#define __PERMEAMETERPARAM_HEADER
 
/* GPIB addresses */
#define GPIB_BOARD_ADDR					0
#define GPIB_PDI5025_ADDR				13
#define GPIB_HP3458_ADDR				24
#define GPIB_B9900_ADDR					17
#define GPIB_S7010_ADDR					10
#define GPIB_GP3_ADDR					16
#define GPIB_LS450_ADDR					15
#define GPIB_LS460_ADDR					17 
#define GPIB_LS475_ADDR					17
#define GPIB_HP3457_ADDR				22
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8
#define GPIB_HP34970_ADDR				9 

/* Email Notification Settings*/
static char MAIL_TO[1000]		=		"sda@slac.stanford.edu";
#define MAIL_SEND_NOTIFICATION			1
#define MAIL_COMPUTER_ID				"Maglab 3"

/* Magnet current */
#define IMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define IMAG_DAC488_ADDR				GPIB_DAC488_ADDR
#define IMAG_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define IMAG_HP34970_ADDR				GPIB_HP34970_ADDR
#define IMAG_DAC488_PORT				2
#define IMAG_DAC488HR_PORT				1
#define IMAG_HP3457_CHAN				0
#define IMAG_HP34970_CHAN				102
#define IMAG_CONFIG						IMAG_DAC488_HP34970
#define IMAG_BIPOLAR					IMAG_TRUE
#define IMAG_PS_AMPS_PER_DAC_VOLT	    1.2
#define IMAG_TRANS_VOLTS_PER_AMP		0.2 
#define IMAG_RAMP_STYLE					IMAG_COSINE
#define IMAG_MAX_CURR_LIMIT				12.0
#define IMAG_MIN_CURR_LIMIT			    -12.0
#define IMAG_RAMP_RATE				    0.2
#define IMAG_WAIT_AFTER_RAMP			5.
#define IMAG_STAND_RAMP_RATE			0.7
#define IMAG_WAIT_AFTER_STAND_RAMP		5.
#define IMAG_INIT_ZERO_CURRENT_MEAS		IMAG_FALSE 
#define IMAG_INIT_TURN_ON				IMAG_FALSE
#define IMAG_INIT_TURN_ON_CURRENT		10.
#define IMAG_CHECK_CURRENT				IMAG_FALSE
#define IMAG_CHECK_CURRENT_TOL			1.0
#define IMAG_SHOW_UI					IMAG_TRUE
#define IMAG_INVERPOWER					IMAG_FALSE
#define IMAG_CHECK_CURRENT_BALLPARK_LIM	   10
#define IMAG_CHECK_CURRENT_TOL_LOWER_LIM   5

/* Hall probe measurements */
#define BHALL_BOARD_ADDR				GPIB_BOARD_ADDR
#define BHALL_B9900_ADDR				GPIB_B9900_ADDR
#define BHALL_GP3_ADDR					GPIB_GP3_ADDR
#define BHALL_LS450_ADDR				GPIB_LS450_ADDR
#define BHALL_LS460_ADDR				GPIB_LS460_ADDR
#define BHALL_LS475_ADDR				GPIB_LS475_ADDR  
#define BHALL_S7010_ADDR			    GPIB_S7010_ADDR
#define BHALL_HP34970_ADDR			    GPIB_HP34970_ADDR
#define BHALL_HP34970_CHAN				115
#define BHALL_ANALOG_TESLA_PER_VOLT		0.10187
#define BHALL_DEVICE_TYPE				BHALL_LS475
#define BHALL_B9900_CHAN				1
#define BHALL_LS460_CHAN				'X'

/* Voltage integration system */
#define VTRAMP_BOARD_ADDR				GPIB_BOARD_ADDR
#define VTRAMP_PDI5025_ADDR				GPIB_PDI5025_ADDR
#define VTRAMP_HP3458_ADDR				GPIB_HP3458_ADDR
#define VTRAMP_PDI5025_CHANNEL			'A'
#define VTRAMP_PDI5025_GAIN				100	// aluminum is 1000 , steel 50
#define VTRAMP_HP3458_RANGE				.1
#define VTRAMP_CONFIG					VTRAMP_HP3458
#define VTRAMP_T_SAMP_BEFORE			0.5
#define VTRAMP_T_SAMP_AFTER				7.
#define VTRAMP_DO_OFFSET_CORRECTION		VTRAMP_TRUE
#define VTRAMP_SHOW_UI					VTRAMP_TRUE

/* BvsH module */
#define BVSH_SAMPLE_GEOMETRY			BVSH_CYLINDER
#define BVSH_CYL_HALL_PROBE_RANGE		3
#define BVSH_CYL_NUM_TURNS_MEAS_COIL	180
#define BVSH_CYL_MEAS_COIL_DIAM			0.020429 //0.020303  // 0.020385  m
#define BVSH_CYL_SAMPLE_OUTER_DIAM		0.018640  // 0.741" or  0.018796 m   Should be 0.741"
#define BVSH_CYL_SAMPLE_INNER_DIAM		0.0048514 // 0.190"  or 0.004826 m.  Should be 11 drill or 191"  0.0048514 m
#define BVSH_RING_NUM_TURNS_DRIVE_COIL	200
#define BVSH_RING_NUM_TURNS_MEAS_COIL	200 
#define BVSH_RING_SAMPLE_OUTER_DIAM		.051808
#define BVSH_RING_SAMPLE_INNER_DIAM		.040454
#define BVSH_RING_SAMPLE_HEIGHT			.007112
#define BVSH_SHOW_UI					BVSH_TRUE


#define BVSH_NUM_STAND_CYCLES			 3
#define BVSH_STAND_MAX					12.
#define BVSH_STAND_MIN					-12.
#define BVSH_NUM_TEST_CURRENTS			177
static double BVSH_TEST_CURRENTS[BVSH_NUM_TEST_CURRENTS] = {0., .006, .012, .02, .04, .06, .08, .09, .1, .12, .14, .16, .18, .20, .225, .25, .275, .3, .325, .35, .375, .4, .425, .45, .475, .5, .525, .55, .575, .6, .65, .7, .75, .8, .85, .9, .95, 1., 1.2,  1.4,  1.6,  1.8,  2., 2.5, 3., 3.5, 4., 4.5, 5., 5.5, 6., 6.5, 7., 8., 9., 10., 12., 10., 9., 8., 7., 6.5, 6., 5.5, 5., 4.5, 4., 3.5, 3., 2.5, 2., 1.5, 1., .8, .6, .4, .2, .18, .16, .14, .12, .1, .08, .06, .04, .02,  .012, .006,  \ 
0., -.006, -.012, -.02, -.04, -.06, -.08,  -.09, -.1, -.12, -.14, -.16, -.18, -.20, -.225, -.25, -.275, -.3, -.325, -.35, -.375, -.4, -.425, -.45, -.475, -.5, -.525, -.55, -.575, -.6, -.65, -.7, -.75, -.8, -.85, -.9, -.95, -1., -1.2, -1.4, -1.6, -1.8, -2., -2.5, -3., -3.5, -4., -4.5, -5., -5.5, -6., -6.5, -7., -8., -9., -10., -12., -10., -9., -8., -7., -6.5, -6., -5.5, -5., -4.5, -4., -3.5, -3., -2.5, -2., -1.5, -1., -.9, -.8, -.7, -.6, -.5, -.4, -.3, -.2, -.18, -.16, -.14, -.12, -.1, -.08, -.06, -.04, -.02,  -.012, -.006, 0.0 };


 
/* End protection */
#endif