%**************************************************************************
%This file contains the parameters used by the insertion device analysis
%comparison program.
%
%Zachary Wolf, 12/24/07

%Parameters
%COMPARE_NAME = 'Laser Heater, 50 micron and 0 micron taper';
%OUTPUT_DIR = 'C:\Magdata\Heater Undulator Sim\Taper 50 mic\';

%INPUT_FILE{1} = 'C:\Magdata\Heater Undulator Sim\Taper 0 mic\id_anal.mat';
%INPUT_FILE{2} = 'C:\Magdata\Heater Undulator Sim\Taper 50 mic\id_anal.mat';

%INPUT_NAME{1} = 'No Taper';
%INPUT_NAME{2} = '50 Micron Taper';

%SN27 Temperature Test ---------------------------
COMPARE_NAME = 'Phase Matching Study';
OUTPUT_DIR = 'C:\Magdata\Phase Matching Study\';

ii = 0;
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 068\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 069\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 070\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 071\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 072\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 073\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 074\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 075\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 076\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 077\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 078\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 079\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 080\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 081\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 082\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 083\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 084\pid_anal.mat';
ii = ii + 1;  INPUT_FILE{ii} = 'S:\MagData\LCLS2\Undulator\HXU-32\DATASET0001\Fine Tuning\Z Scans\Run 085\pid_anal.mat';

ii = 0;
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.2 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.4 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.6 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.8 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 10.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 9.72 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 12.12 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 13.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 15.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 20.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 25.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 8.5 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 8.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 17.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 19.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 21.0 mm';
ii = ii + 1;  INPUT_NAME{ii} = 'Gap = 23.0 mm';
