/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 9/15/98
 */
 
/* Protection from multiple definitions */
#ifndef __PARAM_HEADER
#define __PARAM_HEADER
 
/* GPIB addresses */
#define GPIB_BOARD_ADDR					0
#define GPIB_K7011_ADDR					7
#define GPIB_CM2100_ADDR				1
#define GPIB_PDI5025_ADDR				13
#define GPIB_HP3457_ADDR				22
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8
#define GPIB_VRZ404a_ADDR				29
#define GPIB_VRZ404b_ADDR				30

/* Voltage integration system */
#define VTCOIL_BOARD_ADDR				GPIB_BOARD_ADDR
#define VTCOIL_K7011_ADDR				GPIB_K7011_ADDR
#define VTCOIL_CM2100_ADDR				GPIB_CM2100_ADDR
#define VTCOIL_PDI5025_ADDR				GPIB_PDI5025_ADDR
#define VTCOIL_CONFIG					VTCOIL_K7011_CM2100_PDI5025
#define VTCOIL_NUM_ENC_PULSE_PER_REV	1024
#define VTCOIL_NUM_SAMP_PER_REV			64
#define VTCOIL_MOTOR_ACC				1.6  // was 2. changed to 1.6 sda 5/10/02
#define VTCOIL_MOTOR_VEL				1.
#define VTCOIL_REL_MOTOR_ROT_DIR		-1.
#define VTCOIL_SHOW_UI					VTCOIL_TRUE

/* Field Harmonics */
#define BLHAR_NUM_HAR					16
#define BLHAR_NUM_MAIN_HARMONIC			2
#define BLHAR_NUM_MEAS_AVE				4
#define BLHAR_INTEG_CHAN				'A'
#define BLHAR_NUM_REV_PER_MEAS			8
#define BLHAR_REFERENCE_RADIUS			.004
#define BLHAR_COIL_PARAM_FILE			"..\\CoilParameters\\dc1bq_qadd_param.dat"
#define BLHAR_MAGNET_VIEW				"View from the non labeled end"
#define BLHAR_SHOW_UI					BLHAR_TRUE

/* Magnet current */
#define IMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define IMAG_DAC488_ADDR				GPIB_DAC488_ADDR
#define IMAG_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define IMAG_DAC488_PORT				1
#define IMAG_DAC488HR_PORT				1
#define IMAG_HP3457_CHAN				0
//#define IMAG_CONFIG						IMAG_MANUAL_HP3457
//#define IMAG_CONFIG						IMAG_DAC488_HP3457
#define IMAG_CONFIG						IMAG_NONE
#define IMAG_BIPOLAR					IMAG_FALSE
#define IMAG_PS_AMPS_PER_DAC_VOLT		29.98
#define IMAG_TRANS_VOLTS_PER_AMP		.03333333333
#define IMAG_RAMP_STYLE					IMAG_COSINE
#define IMAG_MAX_CURR_LIMIT				170.
#define IMAG_MIN_CURR_LIMIT				0.
#define IMAG_RAMP_RATE					1.5
#define IMAG_WAIT_AFTER_RAMP			0.1
#define IMAG_STAND_RAMP_RATE			1.5
#define IMAG_WAIT_AFTER_STAND_RAMP		30.
#define IMAG_INIT_ZERO_CURRENT_MEAS		IMAG_FALSE
#define IMAG_INIT_TURN_ON				IMAG_FALSE
#define IMAG_INIT_TURN_ON_CURRENT		15.
#define IMAG_SHOW_UI					IMAG_TRUE

/* Magnet voltage measurements */
#define VMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define VMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define VMAG_K7011_ADDR					GPIB_K7011_ADDR
#define VMAG_DEVICE_TYPE				VMAG_NONE
#define VMAG_HP3457_CHAN				1
#define VMAG_K7011_CARD_NUM				1
#define VMAG_K7011_HP3457_CHAN			1
#define VMAG_K7011_CHAN					8
#define VMAG_SHOW_UI					VMAG_FALSE

/* Temperature measurements */
#define TMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define TMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define TMAG_K7011_ADDR					GPIB_K7011_ADDR
#define TMAG_DEVICE_TYPE				TMAG_HPTHERM_HP3457
#define TMAG_K7011_CARD_NUM				1
#define TMAG_K7011_HP3457_CHAN			1
#define TMAG_SHOW_UI					TMAG_TRUE
#define TMAG_NUM_TMAG_PROBES			6
int TMAG_PROBE_CHAN_NUM[] = {1, 2, 3, 4, 5, 6};
char TMAG_PROBE_NAME[][30] = {"Under Motor", "Water Into Heater", "Mag Support", "Mag Heater", "Mag Endplate", "Ambient"};
//char TMAG_PROBE_NAME[][30] = {"Ambient", "Magnet Coil", "Water In", "Coil Drive Assembly", "MagSteel(near pole)"};

/* Xmag measurements */
#define XMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define XMAG_VRZ404a_ADDR				GPIB_VRZ404a_ADDR
#define XMAG_VRZ404b_ADDR				GPIB_VRZ404b_ADDR
#define XMAG_DEVICE_TYPE				XMAG_VRZ404a_VRZ404b
//#define XMAG_DEVICE_TYPE				XMAG_NONE
#define XMAG_NUM_DEV					2
// From nonlabeled end
char XMAG_DEV_NAME[][40] = {"Heidenhn #0 r magstnd x (left-) (um)", "Heidenhn #1 l magstnd x (left-) (um)"};
//char XMAG_DEV_NAME[][40] = {"Heidenhain #0 stage (in -) (um)", "Heidenhain #1 (-x) position (um)"}; 

/* Ambient measurements */
#define AMBIENT_BOARD_ADDR				GPIB_BOARD_ADDR
#define AMBIENT_HP3457_ADDR				GPIB_HP3457_ADDR
#define AMBIENT_K7011_ADDR				GPIB_K7011_ADDR
#define AMBIENT_MEAS_SYSTEM				AMBIENT_HP3457
#define AMBIENT_K7011_CARD_NUM			1
#define AMBIENT_K7011_HP3457_CHAN		1
#define AMBIENT_SHOW_UI					AMBIENT_FALSE
#define AMBIENT_NUM_SENSORS				3
char AMBIENT_SENSOR_TYPE[][30] = {"AMBIENT_OMHX93AV_RH", "AMBIENT_OMHX93AV_T", "AMBIENT_OMEWSBPA_P"};
int AMBIENT_SENSOR_CHAN_NUM[] = {7, 8, 9};
char AMBIENT_SENSOR_NAME[][30] = {"Relative Humidity (%RH)", "Ambient Temperature (C)", "Barometric Pressure (inHg)"};

/* Measurement parameters */
#define COIL_NUM_STAND_CYCLES			0
#define COIL_STAND_MAX					160.
#define COIL_STAND_MIN					2.

#define COIL_NUM_ITER					19000
#define COIL_NUM_TEST_CURRENTS			1 
double  COIL_TEST_CURRENTS[COIL_NUM_TEST_CURRENTS] =  {0.} ;
#define COIL_NUM_BBA_CURRENTS		    1
//double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1., 1., 1., 1., 1.04, 1.08, 1.12, 1.16, 1.20, 0.625};
//double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1., 1., 1., 1., .96, .92,.88, .84, .80, 0.76};  
double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1.};
#define COIL_MEAS_HAR_FLAG	    0
#define COIL_MEAS_STR_FLAG		    1 


#endif