/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 9/15/98
 */
 
/* Protection from multiple definitions */
#ifndef __PARAM_HEADER
#define __PARAM_HEADER
 
/* GPIB addresses */
#define GPIB_BOARD_ADDR					0
#define GPIB_K7011_ADDR					7
#define GPIB_CM2100_ADDR				1
#define GPIB_PDI5025_ADDR				13
#define GPIB_HP3457_ADDR				22
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8
#define GPIB_VRZ404a_ADDR				29
#define GPIB_VRZ404b_ADDR				30

/* Voltage integration system */
#define VTCOIL_BOARD_ADDR				GPIB_BOARD_ADDR
#define VTCOIL_K7011_ADDR				GPIB_K7011_ADDR
#define VTCOIL_CM2100_ADDR				GPIB_CM2100_ADDR
#define VTCOIL_PDI5025_ADDR				GPIB_PDI5025_ADDR
#define VTCOIL_CONFIG					VTCOIL_K7011_CM2100_PDI5025
#define VTCOIL_NUM_ENC_PULSE_PER_REV	1024
#define VTCOIL_NUM_SAMP_PER_REV			64
#define VTCOIL_MOTOR_ACC				2.  // was 2. changed to 1.6 sda 5/10/02
#define VTCOIL_MOTOR_VEL				1.5
#define VTCOIL_REL_MOTOR_ROT_DIR		-1.
#define VTCOIL_SHOW_UI					VTCOIL_TRUE

/* Field Harmonics */
#define BLHAR_NUM_HAR					16
#define BLHAR_NUM_MAIN_HARMONIC			2
#define BLHAR_NUM_MEAS_AVE				4
#define BLHAR_INTEG_CHAN				'A'
#define BLHAR_NUM_REV_PER_MEAS			8
#define BLHAR_REFERENCE_RADIUS			0.01201
#define BLHAR_COIL_PARAM_FILE			"..\\CoilParameters\\dc2_54qadd_param.dat"
#define BLHAR_MAGNET_VIEW				"Electric Connections on the right"
#define BLHAR_SHOW_UI					BLHAR_TRUE		 /* Either BL panel or Tmag panel

* Magnet current */
#define IMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define IMAG_DAC488_ADDR				GPIB_DAC488_ADDR
#define IMAG_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define IMAG_DAC488_PORT				2
#define IMAG_DAC488HR_PORT				1
#define IMAG_HP3457_CHAN				0
#define IMAG_CONFIG						IMAG_DAC488_HP3457
#define IMAG_BIPOLAR					IMAG_TRUE
#define IMAG_PS_AMPS_PER_DAC_VOLT		1.2
#define IMAG_TRANS_VOLTS_PER_AMP		.25
#define IMAG_RAMP_STYLE					IMAG_THREE_LINEAR
#define IMAG_MAX_CURR_LIMIT				13.
#define IMAG_MIN_CURR_LIMIT				-13.
#define IMAG_RAMP_RATE					1.
#define IMAG_WAIT_AFTER_RAMP			10.
#define IMAG_STAND_RAMP_RATE			1.
#define IMAG_WAIT_AFTER_STAND_RAMP		10.
#define IMAG_INIT_ZERO_CURRENT_MEAS		IMAG_FALSE
#define IMAG_INIT_TURN_ON				IMAG_FALSE
#define IMAG_INIT_TURN_ON_CURRENT		2.
#define IMAG_SHOW_UI					IMAG_TRUE


/* Magnet voltage measurements */
#define VMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define VMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define VMAG_K7011_ADDR					GPIB_K7011_ADDR
#define VMAG_DEVICE_TYPE				VMAG_HP3457
#define VMAG_HP3457_CHAN				1
#define VMAG_K7011_CARD_NUM				1
#define VMAG_K7011_HP3457_CHAN			1
#define VMAG_K7011_CHAN					8
#define VMAG_SHOW_UI					VMAG_FALSE

/* Temperature measurements */
#define TMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define TMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define TMAG_K7011_ADDR					GPIB_K7011_ADDR
#define TMAG_DEVICE_TYPE				TMAG_HPTHERM_HP3457
#define TMAG_K7011_CARD_NUM				1
#define TMAG_K7011_HP3457_CHAN			1
#define TMAG_SHOW_UI					TMAG_FALSE
#define TMAG_NUM_TMAG_PROBES			2
int TMAG_PROBE_CHAN_NUM[] = {3, 6};
char TMAG_PROBE_NAME[][30] = { "Bottom Left Coil", "Ambient"};

/* Xmag measurements */
#define XMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define XMAG_VRZ404a_ADDR				GPIB_VRZ404a_ADDR
#define XMAG_VRZ404b_ADDR				GPIB_VRZ404b_ADDR
//#define XMAG_DEVICE_TYPE				XMAG_VRZ404a_VRZ404b
#define XMAG_DEVICE_TYPE				XMAG_NONE
#define XMAG_NUM_DEV					2
// From nonlabeled end
char XMAG_DEV_NAME[][40] = {"Heidenhn #0 r magstnd x (left-) (um)", "Heidenhain #1 (-x) position (um)"};
//char XMAG_DEV_NAME[][40] = {"Heidenhain #0 stage (in -) (um)", "Heidenhain #1 (-x) position (um)"}; 

/* Ambient measurements */
#define AMBIENT_BOARD_ADDR				GPIB_BOARD_ADDR
#define AMBIENT_HP3457_ADDR				GPIB_HP3457_ADDR
#define AMBIENT_K7011_ADDR				GPIB_K7011_ADDR
#define AMBIENT_MEAS_SYSTEM				AMBIENT_HP3457
#define AMBIENT_K7011_CARD_NUM			1
#define AMBIENT_K7011_HP3457_CHAN		1
#define AMBIENT_SHOW_UI					AMBIENT_FALSE
#define AMBIENT_NUM_SENSORS				3
char AMBIENT_SENSOR_TYPE[][30] = {"AMBIENT_OMHX93AV_RH", "AMBIENT_OMHX93AV_T", "AMBIENT_OMEWSBPA_P"};
int AMBIENT_SENSOR_CHAN_NUM[] = {7, 8, 9};
char AMBIENT_SENSOR_NAME[][30] = {"Relative Humidity (%RH)", "Ambient Temperature (C)", "Barometric Pressure (inHg)"};

/* Measurement parameters */
#define COIL_WARMUP_SECONDS		        1800  
#define COIL_WARMUP_CURRENT		        8.
#define COIL_NUM_STAND_CYCLES		    3
#define COIL_STAND_MAX					12.
#define COIL_STAND_MIN					-12.
#define COIL_NUM_ITER					1
//#define COIL_NUM_TEST_CURRENTS			1
//double  COIL_TEST_CURRENTS[COIL_NUM_TEST_CURRENTS] =  {12.};
#define COIL_NUM_TEST_CURRENTS			49
double  COIL_TEST_CURRENTS[COIL_NUM_TEST_CURRENTS] =  {-12., -11., -10., -9., -8., -7., -6., -5., -4., -3., -2., -1., 0., 1., 2., 3., 4., 5., 6., 7., 8., 9., 10., 11., 12., 11., 10., 9., 8., 7., 6., 5., 4., 3., 2., 1., 0., -1., -2., -3., -4., -5., -6., -7., -8., -9., -10., -11., -12.};
#define COIL_NUM_BBA_CURRENTS		    1	   // Set to one for no BBA
//double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1., 1., 1., 1., 1.04, 1.08, 1.12, 1.16, 1.20, 0.625};
//double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1., 1., 1., 1., .96, .92,.88, .84, .80, 0.76};  
double  COIL_BBA_CURRENTS[COIL_NUM_BBA_CURRENTS] =  {1.};   // Set to 1 for no multiplier
#define COIL_MEAS_HAR_FLAG      0	    
#define COIL_MEAS_STR_FLAG		1 


#endif