/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 6/5/02
 */
 
/* Protection from multiple definitions */
#ifndef __PARAM_HEADER
#define __PARAM_HEADER
 
/* GPIB addresses */					
#define GPIB_BOARD_ADDR					0
#define GPIB_HP3457_ADDR				22
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8
#define GPIB_TDS754D_ADDR				1

/* Calibration magnet current */
#define IAUX_BOARD_ADDR					GPIB_BOARD_ADDR
#define IAUX_DAC488_ADDR				GPIB_DAC488_ADDR
#define IAUX_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IAUX_HP3457_ADDR				GPIB_HP3457_ADDR
#define IAUX_DAC488_PORT				1
#define IAUX_DAC488HR_PORT				1
#define IAUX_HP3457_CHAN				3
#define IAUX_CONFIG						IAUX_MANUAL_HP3457
#define IAUX_BIPOLAR					IAUX_FALSE
#define IAUX_PS_AMPS_PER_DAC_VOLT		120.
#define IAUX_TRANS_VOLTS_PER_AMP		2.
#define IAUX_RAMP_STYLE					IAUX_THREE_LINEAR
#define IAUX_MAX_CURR_LIMIT				3.
#define IAUX_MIN_CURR_LIMIT				0.
#define IAUX_RAMP_RATE					10.
#define IAUX_WAIT_AFTER_RAMP			1.
#define IAUX_STAND_RAMP_RATE			10.
#define IAUX_WAIT_AFTER_STAND_RAMP		1.
#define IAUX_INIT_ZERO_CURRENT_MEAS		IAUX_FALSE
#define IAUX_INIT_TURN_ON				IAUX_FALSE
#define IAUX_INIT_TURN_ON_CURRENT		15.
#define IAUX_SHOW_UI					IAUX_FALSE

/* Bt system */
#define BTWIRE_BOARD_ADDR					GPIB_BOARD_ADDR
#define BTWIRE_TDS754D_ADDR					GPIB_TDS754D_ADDR
#define BTWIRE_CONFIG						BTWIRE_TDS754D
#define BTWIRE_CHAN_X_WIRE_POS_SENSOR		1
#define BTWIRE_CHAN_Y_WIRE_POS_SENSOR		2
#define BTWIRE_CHAN_WIRE_CURRENT_SENSOR		3
#define BTWIRE_SCALE_X_WIRE_POS_SENSOR		.02
#define BTWIRE_SCALE_Y_WIRE_POS_SENSOR		.02
#define BTWIRE_SCALE_WIRE_CURRENT_SENSOR	2.
#define BTWIRE_SCALE_HORIZONTAL				200.e-6
#define BTWIRE_WIRE_CURRENT_SENSOR_V_PER_A	.1
#define BTWIRE_BX_PER_A_CALIB_MAGNET_BX1	12.6e-4
#define BTWIRE_BX_PER_A_CALIB_MAGNET_BX2	12.5e-4
#define BTWIRE_BY_PER_A_CALIB_MAGNET_BY1	12.6e-4
#define BTWIRE_BY_PER_A_CALIB_MAGNET_BY2	12.5e-4
#define BTWIRE_ZPOS_CALIB_MAGNET_BX1		.116
#define BTWIRE_ZPOS_CALIB_MAGNET_BX2		.352
#define BTWIRE_ZPOS_CALIB_MAGNET_BY1		.116
#define BTWIRE_ZPOS_CALIB_MAGNET_BY2		.352
#define BTWIRE_NOMINAL_WAVE_SPEED			320.
#define BTWIRE_SHOW_UI						BTWIRE_TRUE

/* End protection */
#endif