/*	**************************************************************	*/

/*
 * PARAM.H
 * This file contains parameters required by the measurement
 * program.
 *
 * Zachary Wolf
 * 4/13/00
 */
 
/* Protection from multiple definitions */
#ifndef __TMAGPARAM_HEADER
#define __TMAGPARAM_HEADER
 
/* GPIB addresses */
#define GPIB_BOARD_ADDR					0
#define GPIB_HP3457_ADDR				22
#define GPIB_K7011_ADDR					7
#define GPIB_DAC488_ADDR				19
#define GPIB_DAC488HR_ADDR				8
#define GPIB_VRZ404a_ADDR				29
#define GPIB_VRZ404b_ADDR				30

/* Magnet voltage measurements */
#define VMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define VMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define VMAG_K7011_ADDR					GPIB_K7011_ADDR
#define VMAG_DEVICE_TYPE				VMAG_HP3457
#define VMAG_HP3457_CHAN				1
#define VMAG_K7011_CARD_NUM				1
#define VMAG_K7011_HP3457_CHAN			1
#define VMAG_K7011_CHAN					8
#define VMAG_SHOW_UI					VMAG_FALSE

/* Magnet current */
#define IMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define IMAG_DAC488_ADDR				GPIB_DAC488_ADDR
#define IMAG_DAC488HR_ADDR				GPIB_DAC488HR_ADDR
#define IMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define IMAG_DAC488_PORT				1
#define IMAG_DAC488HR_PORT				1
#define IMAG_HP3457_CHAN				0
#define IMAG_CONFIG						IMAG_MANUAL_HP3457
#define IMAG_BIPOLAR					IMAG_FALSE
#define IMAG_PS_AMPS_PER_DAC_VOLT		240.
#define IMAG_TRANS_VOLTS_PER_AMP		.01
#define IMAG_RAMP_STYLE					IMAG_THREE_LINEAR
#define IMAG_MAX_CURR_LIMIT				300.
#define IMAG_MIN_CURR_LIMIT				0.
#define IMAG_RAMP_RATE					15.
#define IMAG_WAIT_AFTER_RAMP			3.
#define IMAG_STAND_RAMP_RATE			15.
#define IMAG_WAIT_AFTER_STAND_RAMP		3.
#define IMAG_INIT_ZERO_CURRENT_MEAS		IMAG_FALSE
#define IMAG_INIT_TURN_ON				IMAG_FALSE
#define IMAG_INIT_TURN_ON_CURRENT		25.
#define IMAG_SHOW_UI					IMAG_FALSE

/* Temperature measurements */
#define TMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define TMAG_HP3457_ADDR				GPIB_HP3457_ADDR
#define TMAG_K7011_ADDR					GPIB_K7011_ADDR
#define TMAG_DEVICE_TYPE				TMAG_THERMISTOR_HP3457
#define TMAG_K7011_CARD_NUM				1
#define TMAG_K7011_HP3457_CHAN			1
#define TMAG_SHOW_UI					TMAG_FALSE
#define TMAG_NUM_TMAG_PROBES			7
int TMAG_PROBE_CHAN_NUM[] = {2,3,4,5,8,9,1};
char TMAG_PROBE_NAME[][30] = {"Water In (C)", "Water Out (C)", "Magnet Steel (C)", "Magnet Coil Upper (C)", "Magnet Coil Lower (C)", "Measurement Coil (C)", "Ambient (C)"};

/* Xmag measurements */
#define XMAG_BOARD_ADDR					GPIB_BOARD_ADDR
#define XMAG_VRZ404a_ADDR				GPIB_VRZ404a_ADDR
#define XMAG_VRZ404b_ADDR				GPIB_VRZ404b_ADDR
#define XMAG_DEVICE_TYPE				XMAG_VRZ404a_VRZ404b
#define XMAG_NUM_DEV					2
char XMAG_DEV_NAME[][40] = {"Heidenhain #0 position (m)", "Heidenhain #1 position (m)"};
 
/* End protection */
#endif